- 您现在的位置：买卖IC网 > Sheet目录201 > A8L-11-11N2 (Omron Electronics Inc-EMC Div)SWITCH ROCKER MINI SPST VERT SLD
Precautions
■ Correct Use
Mounting
Turn OFF the power supply before mounting, removing or wiring the
Switch, or before performing maintenance inspections. Failure to do
so may result in electric shock.
Do not use panels other than ones with the designated thickness and
dimensions. Remove all burrs from the cutout before installing the
Switch. Otherwise, the Switch may malfunction.
Do not impose excessive force on the Switch at the time of panel-
mounting.
There are two small divots in the flange part of the case marking ON
and OFF as shown in the following diagram. Use these marks as
guides when mounting.
■ Cautions
Do not wire the Switch or touch any terminal of the
Switch While power is being supplied. Doing so may
result in electric shock.
To increase the reliability of operation, test the Switch before actual
operation.
Be sure that there is an enough insulation distance between any
Switch terminal and metal part.
Handling
Do not drop the Switch. Otherwise, the Switch may malfunction.
Do not impose excessive force on the Switch. Otherwise, the Switch
may deform.
Wiring
OFF
ON
The recommended panel material is SPCC. The Switch may fall off if
the material is soft and cannot securely hold the Switch. When using
a soft material, test the Switch with it before using the Switch in
actual operation.
When soldering terminals manually, perform soldering within 3 s
using a 60-W soldering iron (temperature at the tip of the soldering
iron: 420 ° C max.). Do not apply excessive force to the terminals dur-
ing soldering.
When soldering using a soldering tub, perform soldering within 5 s in
a soldering fluid at 270 ° C, or within 3 s in a soldering fluid at 350 ° C.
Be sure that the wires are thick enough for the load (current) to be
applied.
Only A8L- @@ - @ 5 @@ models are equipped with (6.3 × 0.8) mm flat-
quick connections for use with #187 fasten receptacles.
The terminals of A8L- @@ - @ 1 @@ are not in compliance with IEC
standards for flat-quick connections. Suitable for use as solder con-
nection only.
Using Microloads
The performance of the Switch may be affected if the Switch is used
for switching micro loads. Test the Switch under the actual operating
conditions.
Operating Environment
Do not use the Switch in places with sulfide gas, corrosive gas, sea
breeze, oil spray, or direct sunlight. Otherwise, the Switch may mal-
function.
Do not use the Switch in places that are visibly dusty. Otherwise, the
contacts may fail to operate correctly.
4
Miniature Rocker Switch
A8L
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
A8L-21-13N2
SWITCH ROCKER DPST RT ANG 10A
A9PS26-0013
SWITCH PUSH DPST-NO 0.1A 28V
AA-12.288MAGV-T
CRYSTAL 12.288 MHZ 8 PF SMD
AB-16.000MALE-T
CRYSTAL 16.000 MHZ 12 PF SMD
AB-2.000MHZ-B2
CRYSTAL 2.000MHZ 18PF HC49/U
AB15T-32.768KHZ
CRYSTAL 32.768KHZ 12.5PF CYL
AB25AV-HB
SWITCH PUSH DPDT 0.4VA 28V
AB26TRB-32.768KHZ-T
CRYSTAL 32.768KHZ 12.5PF CYL SMD
相关代理商/技术参数
A8L-11-11N3
制造商:OMRON 制造商全称:Omron Electronics LLC 功能描述:Miniature Rocker Switch
A8L1111N6
制造商:Omron Corporation 功能描述:ROCKER SWITCH - Trays
A8L-11-11N6
制造商:OMRON 制造商全称:Omron Electronics LLC 功能描述:Miniature Rocker Switch
A8L1112N1
制造商:Omron Electronic Components LLC 功能描述:Switch Rocker ON OFF SPST PC Pins Curved Rocker 10A 250VAC 50000Cycle Box
A8L-11-12N1
制造商:Omron Electronic Components LLC 功能描述:Switch Rocker ON OFF SPST PC Pins Curved Rocker 10A 250VAC 50000Cycle Box
A8L1112N2
制造商:Omron Electronic Components LLC 功能描述:Switch Rocker ON OFF SPST PC Pins Curved Rocker 10A 250VAC 50000Cycle Box
A8L-11-12N2
制造商:Omron Electronic Components LLC 功能描述:Switch Rocker ON OFF SPST PC Pins Curved Rocker 10A 250VAC 50000Cycle Box
A8L-11-12N3
制造商:OMRON 制造商全称:Omron Electronics LLC 功能描述:Miniature Rocker Switch